Gamberini, Gaia
(2026)
Characterization of sapphire material as substrate for high energy physics detectors.
[Laurea magistrale], Università di Bologna, Corso di Studio in
Physics [LM-DM270]
Documenti full-text disponibili:
Abstract
In modern High Energy Physics, the extreme radiation environments of upcoming facilities, ranging from future fusion reactors to the High-Luminosity LHC (HL-LHC), increasingly expose the operational limits of traditional silicon-based detectors. Sapphire (Al2O3) emerges as a highly promising wide-band gap alternative, offering minimal intrinsic dark current, cost-effective production, and
high radiation hardness. Its implementation as an active sensor is currently limited by a low intrinsic CCE of approximately 5 %, caused by structural lattice defects that act as deep charge-trapping centers within the crystal. Conducted within the framework of the INFN SLBP project, this thesis investigates methodologies to optimize sapphire substrates and characterizes their performance under both laboratory and particle beam conditions. The initial phase of this research focused on the material preparation and characterization of a 100 µm thick sapphire substrate at the DiATHEMA laboratory (CNR-ISM). High-temperature annealing was employed to promote Frenkel pair recombination, aiming to reduce the trap. The structural effects of this thermal processing were evaluated using Raman spectroscopy alongside Scanning Probe Microscopy (SPM). The detectors were fabricated by depositing metal electrodes via sputtering, using three metallization schemes to identify the optimal metal-sapphire contact. Following metallization, dark current measurements were conducted. To characterize the material’s interaction with ionizing radiation, the sapphire samples were irradiated using an X-ray tube across a range of bias voltages, beam intensities, and emission energies. Finally, the response of the sapphire prototype was evaluated via an electron beam test at the BTF (INFN-LNF), characterizing the pad sensor as a function of beam position, intensity, and applied bias voltage. The measurements confirmed that the pad response scales proportionally
with both the beam intensity and the applied bias.
Abstract
In modern High Energy Physics, the extreme radiation environments of upcoming facilities, ranging from future fusion reactors to the High-Luminosity LHC (HL-LHC), increasingly expose the operational limits of traditional silicon-based detectors. Sapphire (Al2O3) emerges as a highly promising wide-band gap alternative, offering minimal intrinsic dark current, cost-effective production, and
high radiation hardness. Its implementation as an active sensor is currently limited by a low intrinsic CCE of approximately 5 %, caused by structural lattice defects that act as deep charge-trapping centers within the crystal. Conducted within the framework of the INFN SLBP project, this thesis investigates methodologies to optimize sapphire substrates and characterizes their performance under both laboratory and particle beam conditions. The initial phase of this research focused on the material preparation and characterization of a 100 µm thick sapphire substrate at the DiATHEMA laboratory (CNR-ISM). High-temperature annealing was employed to promote Frenkel pair recombination, aiming to reduce the trap. The structural effects of this thermal processing were evaluated using Raman spectroscopy alongside Scanning Probe Microscopy (SPM). The detectors were fabricated by depositing metal electrodes via sputtering, using three metallization schemes to identify the optimal metal-sapphire contact. Following metallization, dark current measurements were conducted. To characterize the material’s interaction with ionizing radiation, the sapphire samples were irradiated using an X-ray tube across a range of bias voltages, beam intensities, and emission energies. Finally, the response of the sapphire prototype was evaluated via an electron beam test at the BTF (INFN-LNF), characterizing the pad sensor as a function of beam position, intensity, and applied bias voltage. The measurements confirmed that the pad response scales proportionally
with both the beam intensity and the applied bias.
Tipologia del documento
Tesi di laurea
(Laurea magistrale)
Autore della tesi
Gamberini, Gaia
Relatore della tesi
Correlatore della tesi
Scuola
Corso di studio
Indirizzo
NUCLEAR AND SUBNUCLEAR PHYSICS
Ordinamento Cds
DM270
Parole chiave
Sapphire,detectors,HEP,annealing,metallization,sputtering,ionization,test beam,x-ray gun,electron beam,data analysis,sample preparation,material characterization,prototype testing,raman spectroscopy,Atomic Force Microscopy
Data di discussione della Tesi
28 Ottobre 2026
URI
Altri metadati
Tipologia del documento
Tesi di laurea
(NON SPECIFICATO)
Autore della tesi
Gamberini, Gaia
Relatore della tesi
Correlatore della tesi
Scuola
Corso di studio
Indirizzo
NUCLEAR AND SUBNUCLEAR PHYSICS
Ordinamento Cds
DM270
Parole chiave
Sapphire,detectors,HEP,annealing,metallization,sputtering,ionization,test beam,x-ray gun,electron beam,data analysis,sample preparation,material characterization,prototype testing,raman spectroscopy,Atomic Force Microscopy
Data di discussione della Tesi
28 Ottobre 2026
URI
Statistica sui download
Gestione del documento: